 |
 | | Designed, manufactured and tested to the applicable portions of
MIL-F-15733.
Each individual filter circuit is replaceable in the field without the
use of special tools.
Each individual filter circuit is hermetically sealed.
Terminals: Each circuit is terminated with a flexible lead to an electrical
standoff preventing damage to the terminals.
Maximum voltage drop: 2 Volts
Maximum operating temperature 85°C
Overload safety: 140% rated current for 15 minutes.
Case: Steel all welded construction suitably plated on grounding surfaces
and painted or plated on all other surfaces.
|
|
|
|
|
 | | Designed and manufactured
by MTK
Unit hermetically sealed
Case: Metal, suitably plated
to withstand corrosion.
|
|
|
|
|
 | | Designed, manufactured and tested to
the applicable portions of MIL-F-15733.
Case: Metal, suitably plated to withstand corrosion.
Economical.
|
|
|
|
|
 | | Designed, manufactured and tested to the
applicable portions of MIL-F-15733.
Filter hermetically sealed. Penetration is terminated with a flexible lead.
Maximum voltage drop: 2 Volts.
Maximum operating temperature 85ºC
Overload Safety: 140% rated current for 15 minutes.
Case; Steel suitably plated to withstand corrosion.
|
|
|
|
|
 | | Current: (see table)
Freq.: 60 HZ
Voltage: 277 VAC
Atten: 100DB@14 KHZ
Mat’l: Solder plated CRS
Internal construction encapsulated
|
|
|
|
|
 | | Operating temperature: 55°C to + 125°C
DC resistance: 0.01 OHMS max.
Capacitance tolerance:+-
20%
Dielectric test: 2 X rated voltage.
Conforms to applicable requirements of MIL-C-11693.
known as feed thru capacitors.
|
|
|
|
|
 | | Designed, manufactured and tested to the applicable portions of MIL-F-15733.
Pass band insertion loss measured in a 300 ohm system per MIL-STD-220A
(Applicable to telephone filters only).
Stop band insertion loss measured in a 50 ohm system per MIL-STD-220A.
Case: Steel suitably plated to withstand corrosion.
Filters can be supplied installed in cabinets as shown on next page.
|
|
|
|
|
 | | Designed, manufactured and tested to the applicable portions of MIL-F-15733.
Filter hermetically sealed.
Also known as tubular filters.
Case: Metal, suitably plated to withstand corrosion.
|
|
|
|
|
 | | Designed, manufactured and tested to the applicable portions of MIL-F-15733.
Filter hermetically sealed.
Case: Metal, suitably plated to withstand corrosion.
Also known as tubular filters.
|
|
|
|
|
 | | Designed, manufactured and tested to the applicable portions
of MIL-F-15733.
Filter hermetically sealed.
Case: Metal, suitably plated to withstand corrosion.
Also known as tubular filters.
|
|
|
|
|
 | | Designed, manufactured and tested to the applicable portions of MIL-F-15733.
Filter hermetically sealed.
Maximum operating temperature: 85ºC
Overload safety: 140% rated current for 15 minutes.
Case: Steel, suitably plated to withstand corrosion.
|
|
|
|
|
 | | INSERTION LOSS
The two digits next to the basic part number under the column marked db is
the insertion loss for that filter at a frequency of 150 kilohertz. The symbol db
stands for decibels which is a logorithmic ratio of signal input to signal output
when measured in a 50 ohm circuit. The higher the decibel number the greater
the interference reducing ability of the filter.
The rectangular filters shown have an effective range of performance from
below 150 kilohertz to about 400 megahertz. The tubular filters shown are
effective from below 150 kilohertz to 10 gigahertz.
|
|
|
|
|
 | | The above model 2393 filtered terminal block demonstrates just one of
a virtually infinite number of variations that may be manufactured to your
requirements.
These specially molded filtered terminal blocks can be provided in various
lengths. Currents and capacitances to fit your requirements. Wires may be
color coded or marked with lengths as required
Call factory to discuss your requirements.
|
|
|
|
|
 | | |
|
|
|
|
 | | |
